Sachiya Steel International is one of the prominent Manufacture and Exporter of Stainless Steel 317L Wire Mesh, which is one of the most sustainable material choices available to decision makers. The work – hardening property of austenitic SS 317L Hexagonal Wire Mesh, that results in a significant strengthening of the material from cold – working alone, and the high strength allow reduced material thickness over conventional grades, therefore cost savings. Modern steel – making techniques mean that Stainless Steel 317L Welding Wire Mesh can be cut, welded, formed, machined, and fabricated as readily as traditional steels.
SS 317L Netting Wire Mesh has good strength and good resistance to corrosion and oxidation at elevated temperatures. Stainless Steel 317L Woven Wire Mesh is used at temperatures up to 1700 Degree F and up to 2000 Degree F for the high temperature stainless grade. SS 317L Spring Steel Wire Mesh is used extensively in heat exchangers, super – heaters, boilers, feed water heaters, valves and main steam lines as well as aircraft and aerospace applications.
With time and temperature, changes in metallurgical structure of Stainless Steel 317L Fencing Wire Mesh can be expected with any metal. In 317L Stainless Steel Wire Mesh, the changes can be softening, carbide precipitation, or embrittlement. Softening or loss of strength occurs in SS 317L Wire Mesh at about 1000 Degree F and at about 900 Degree F for the harden able series and 800 Degree F for the non – harden able series.
|
SS 317L Wiremesh Specifications
|
||
| Specifications | : | ASTM A 164 ASME SA 164 |
| Standard | : | ASTM, AISI International Standards |
| Length | : | 30m to 100″ |
| Width | : | 1m to 48″ |
| Type | : | Wire Mesh , Hexagonal Wire mesh, Welding Wire mesh, Netting Wire mesh, Woven Wire mesh , Spring Steel wire mesh, Fencing Wire mesh etc. |
| Grade | C | Mn | Si | P | S | Cr | Mo | Ni | Fe |
| SS 317L | 0.035 max | 2 max | 1.00 max | 0.045 max | 0.030 max | 18.00 – 20.00 | 3.00 – 4.00 | 11.00 – 15.00 | 57.89 min |
| Density | Melting Point | Tensile Strength | Yield Strength (0.2%Offset) | Elongation |
| 7.9 g/cm3 | 1400 °C (2550 °F) | Psi – 75000 , MPa – 515 | Psi – 30000 , MPa – 205 | 35 % |
| STANDARD | WERKSTOFF NR. | UNS | JIS | BS | GOST | AFNOR | EN |
| SS 317L | 1.4438 | S31703 | SUS 317L | – | – | – | X2CrNiMo18-15-4 |
- Off-Shore Oil Drilling Companies
- Power Generation
- Petrochemicals
- Gas Processing
- Specialty Chemicals
- Pharmaceuticals
- Pharmaceutical Equipment
- Chemical Equipment
- Sea Water Equipment
- Heat Exchangers
- Condensers
- Pulp and Paper Industry
Sachiya Steel International is one of the prominent Manufacture of high quality Stainless Steel 310H Wire Mesh, which Good resistance to mildly corrosive atmospheres, but significantly less than Grade 310H due to the Sulphur addition; the sulphide inclusions act as pit initiation sites.
Grade 310 should not be exposed to marine or other similar environments, as these will result in rapid pitting corrosion.
Because the sulphide inclusions in 310 are primarily aligned along the rolling direction the corrosion resistance is particularly reduced in cross-sections.It is like other common austenitic stainless steels, is subject to stress corrosion cracking in chloride containing environments above about 50°C.
Good oxidation resistance in intermittent service to 760°C and in continuous service to 870°C.
Welds must be annealed for maximum corrosion resistance, but even then poor mechanical and corrosion properties will result.For ultra-high machining rates there are also available special grade variants such as Ugima 303UX.
This includes copper to reduce the work hardening rate, in addition to the usual high Sulphur and Improved Machinability steel making practices.
