Stainless Steel 347H Wire Mesh Manufacture

Sachiya Steel International is one of the prominent Manufacture of high quality Stainless Steel 310H Wire Mesh, which Good resistance to mildly corrosive atmospheres, but significantly less than Grade 310H due to the Sulphur addition; the sulphide inclusions act as pit initiation sites.

Grade 310 should not be exposed to marine or other similar environments, as these will result in rapid pitting corrosion.

Because the sulphide inclusions in 310 are primarily aligned along the rolling direction the corrosion resistance is particularly reduced in cross-sections.It is like other common austenitic stainless steels, is subject to stress corrosion cracking in chloride containing environments above about 50°C.

Good oxidation resistance in intermittent service to 760°C and in continuous service to 870°C.

Welds must be annealed for maximum corrosion resistance, but even then poor mechanical and corrosion properties will result.For ultra-high machining rates there are also available special grade variants such as Ugima 303UX.

This includes copper to reduce the work hardening rate, in addition to the usual high Sulphur and Improved Machinability steel making practices.

Sachiya Steel International is one of the Leading Manufacturer And Exporter of Stainless Steel 347H Round Bar, which are often quenched in water making them adapted for the production of parts with a simple form and not particularly difficult uses such as pivots and bushings.

In conditions, where the corrosion and heat resistance of Stainless Steel 347H Square Bars and other metals are exhausted, high performance alloys including Nickel become the designer’s material of choice.

In aero engines, the combination of Stainless Steel 347H Flat Bars for the cooler compressor areas and nickel super – alloys for the hot gas path in the turbine, enable an optimized weight and performance ratio to be achieved.In fuselage applications, the strength characteristics and corrosion resistance of Stainless Steel 347H Threaded Bars provide them with a role in both structural areas and for fasteners.

Even in composite mould tooling, Stainless Steel 347H Hollow Bars are used to take advantage of their low thermal expansion features.

Although its weight and low strength characteristics deny it wide application in aerospace products, Stainless Steel 347H Hexagonal Bars nonetheless is an important element in the design of electrical systems, transformer and heat exchanger applications.Stainless Steel 347H Round Bar | Stainless Steel 347H Round Bar | Stainless Steel 347H Round Bar | Stainless Steel 347H Round Bar | Stainless Steel 347H Round Bar | Stainless Steel 347H Round Bar | Stainless Steel 347H Round Bar  | Stainless Steel 347H Round Bar | Stainless Steel 347H Round BarQuenched of Stainless Steel 347H Triangular Bars are limited in their tempering potential and so accuracy can only be obtained on smaller parts.

Special high chromium and nickel – alloyed 347H Stainless Steel Bars resist scaling and retain strength at high temperatures.SS 347H Round Bar SpecificationsSpecifications:ASTM A276, ASME SA276 / ASTM A479  ASME SA479Dimensions:EN, DIN, JIS, ASTM, BS, ASME, AISISS 347H Round Bars:Outside Diameter in the range of 4mm to 500mmSS 347H Bright Bars:Outside Diameter in the range of 4mm to 100mmSS 347H Hex Bars:18mm – 57mm (11/16″ to 2-3/4″)SS 347H Square Bars:18mm – 47mm (11/16″ to 1-3/4″)SS 347H Flat Bars:1/2” to 10” in thickness range of 2mm to 150mm,Finish:Black, Bright Polished, Rough Turned, NO.4 Finish, Matt Finish, BA FinishLength:1 to 6 Meters, Custom Cut LengthsForm:Round, Square, Hex (A/F), Rectangle, Billet, Ingot, Forging Etc.347H Stainless Steel Round Bar Chemical CompositionGradeCMnSiPSCrCbNiFeSS 3470.04 – 0.102 max1.0 max0.045 max0.030 max17 –198xC – 1.109.0-13.062.72 minStainless Steel 347H Rods Mechanical PropertiesDensityMelting PointTensile StrengthYield Strength (0.2%Offset)Elongation8.0 g/cm31454 °C (2650 °F)Psi – 75000 , MPa – 515Psi – 30000 , MPa – 20535 %Equivalent Grades for 347H Stainless Steel Round BarSTANDARDWERKSTOFF NR.UNSJISBSGOSTAFNORENSS 347H1.4961S34709SUS 347H–––X6CrNiNb18-12SS 347H Round Bar Application IndustriesOff-Shore Oil Drilling CompaniesPower GenerationPetrochemicalsGas ProcessingSpecialty ChemicalsPharmaceuticalsPharmaceutical EquipmentChemical EquipmentSea Water EquipmentHeat ExchangersCondensersPulp and Paper IndustryAbout Us: Sachiya Steel International are manufacturers & exporters of Pipes,Tubes ,Pipe Fitting, Fasteners.Sachiya Steel International is an internationally acclaimed Pipes And Tubes manufacturing company that exports to more than 90 countries worldwide.

Sachiya Steel International is one of the Leading Manufacturer And Exporter of Stainless Steel 347H Pipe Fittings, which are often specified when high strength is needed in moderate – to – large sections.

Whether tensile or yield strength is the basis of design, thermally treated Stainless Steel 347H Compression Pipe Fittings generally offer high strength – to – weight ratios.

For applications requiring maximum ductility, SS 347H Compression Fittings with low Sulphur levels can be supplied by producers using ladle – refining techniques.In general, wear resistance can be improved by increasing the hardness of these Stainless Steel 347H Ferrule Pipe Fittings, by specifying an alloy with greater carbon content (without increasing hardness), or by both.

The surface of flame – hardened, medium – carbon steel, for example, Stainless Steel 347H Double Ferrule Pipe Fittings is likely to have poorer wear resistance than the carbon – rich case of a carburized steel of equal hardness.Stainless Steel 347H Pipe Fittings | Stainless Steel 347H Pipe Fittings | Stainless Steel 347H Pipe Fittings | Stainless Steel 347H Pipe Fittings | Stainless Steel 347H Pipe Fittings Exceptions are nitride parts of these 347H Stainless Steel Compression Pipe Fittings, which have better wear resistance than would be expected from the carbon content alone.

For any combination of 347H SS Ferrule Pipe Fittings and heat treatment, three factors tend to decrease toughness: low service temperature, high loading rates, and stress concentrations or residual stress.

However, care is necessary for both cold and hot worked materials because these 347H Stainless Steel Double Ferrule Pipe Fittings have high strength.Stainless Steel 347H Pipe Fittings / Accessories SpecificationsSpecifications:ASTM A182 ASME SA 182Tube Size:1/16”OD to 2”OD, 2mm OD to 50mm ODThread:NPT, BSP, BSPT, UNF, ISO, SAE etc.Pressure Rating:6000PSI for Stainless Steel, 300/1000/3000PSI for BrassSS 347H Pipe Fittings Chemical CompositionGradeCMnSiPSCrCbNiFeSS 347H0.04 – 0.102.0 max1.0 max0.045 max0.030 max17.00 – 20.008xC – 1.109.00 – 13.0063.72 minStainless Steel 347H Accessories Mechanical PropertiesDensityMelting PointTensile StrengthYield Strength (0.2%Offset)Elongation8.0 g/cm31454 °C (2650 °F)Psi – 75000 , MPa – 515Psi – 30000 , MPa – 20535 %Equivalent Grades for 347H Stainless Steel Pipe FittingsSTANDARDWERKSTOFF NR.UNSJISBSGOSTAFNORENSS 347H1.4961S34709SUS 347H–––X6CrNiNb18-12SS 347H Pipe Fittings / Accessories Application IndustriesOff-Shore Oil Drilling CompaniesPower GenerationPetrochemicalsGas ProcessingSpecialty ChemicalsPharmaceuticalsPharmaceutical EquipmentChemical EquipmentSea Water EquipmentHeat ExchangersCondensersPulp and Paper IndustryAbout Us: Sachiya Steel International are manufacturers & exporters of Pipes,Tubes ,Pipe Fitting, Fasteners.Sachiya Steel International is an internationally acclaimed Pipes And Tubes manufacturing company that exports to more than 90 countries worldwide.

Stainless Steel Wire Mesh Manufacturers in Delhi - Find Stainless Steel Wire Mesh panels, suppliers, manufacturers, dealers & exporters company in India.

Get contact details - 098102 53450.