logo
logo
AI Products 

Ampedwireless Login | http //setup.ampedwireless.com | 192.168.1.240

avatar
KnightRides
Ampedwireless Login | http //setup.ampedwireless.com | 192.168.1.240

Amped wireless setup | http //setup.ampedwireless.com


http://www.setup.ampedwireless.com is a local web address used to access and to configure amped wireless networking devices like routers, extenders, modems, and USB adapters. It permits login to the web-based interface for amped wireless.

How to setup amped wireless router through setup.ampedwireless.com or 192.168.1.240

  • If you have an earlier Wi-Fi router begin by connecting it out of your modem and your laptop and computer.
  • Establish connection between the Amped wireless router as well as your modem with an Ethernet cable that is used to connect the modem to one end , and to the WAN port on the Amped wireless router on the other.
  • Shut off your modem, as well as your router by disconnecting the power cable to them for approximately 10 minutes.
  • Connect them to their power source and then start the modem and then wait for one minute, then proceed and switch on the Amped Wireless router.
  • Also, connect to the wireless router and your computer device using the Ethernet cable.
  • Launch a web browser and type http://setup.ampedwireless.com as the web address in address bar of your browser
  • The login screen will appear, but when you set up for the first time, you will be presented with a setup screen for configuration.
  • It appears that the Smart Setup Wizard appears and it will automatically begin the setup process once you have clicked the Start Setup option. The Setup Wizard will direct users to follow the complete internet connection configuration by providing on-screen instructions.
  • Select"Automatic Configuration" in order to allow to configure the Amped wireless router to be automatically configured with the suggested settings. Select Next.
  • You have the option of entering an SSID or Network name for the router.

This Amped Wireless router is finally installed and working properly. Now you can customize your network even more.

Do I configure my amplified wireless range extender?

This is possible when your Wi-Fi device supports WPS one-touch configuration by following the following steps

  • Find the WPS button on the back in Your Amped wireless router. Press and hold it for around 2 to 3 minutes.
  • You'll notice that the power LED on the wireless router will start to blink.
  • While you're at it push the WPS button on your wireless adapter . You can also activate WPS by using the software that comes with your wireless adapter.
  • After that, WPS will automatically configure and set the settings for the connection of your wireless adapter , which will connect directly to the Amped wireless router.

If Setup.ampedwireless.com is not responding?

Sometimes when you are trying to access setup.ampedwireless.com, you may see an error message that the page cannot be displayed or a bad gateway error.

In this scenario first it is important to ensure that an Ethernet cable from the wireless router has been connected to your computer in a proper manner.

Do not connect your computer wirelessly with an amplified wireless router. If there is any chance that the computer you're using is linked to an different wireless network, attempt to disable the Wi-Fi adapter in your device and after that ensure that firewall software is blocked.

How do set you Amped Wireless router?

Amped wireless router can be reset. Amped wireless router is able to be reset to default settings in the below methods:

Clicking the button Reset

Utilizing the web interface of the router by utilizing the web interface

Resetting your device using the reset button is an easy and fast if you follow the steps listed below:

  • Find the reset/restore button which is located in the rear of the router.
  • Utilizing an unstraightened paper clip or pin press the reset button and continue pressing your reset button around 10 seconds before releasing it.
  • You should wait for a couple of minutes before the LED light begins to flash , which is the indication that your Amped Wireless router is restored to its default settings.

Resetting the router through web interface, you must sign in to the interface on the internet of the amplified wireless router

  • Go to www.setup.ampedwireless.com through a web browser.
  • Log in with your login credentials of default to gain access to the admin page of the wireless amped.
  • Visit the settings page, and then select the factory reset option which will bring the router back to its factory settings.

What if you are unable to open the web menu of the amped wireless router after you enter the www.setup.ampedwireless.com?

  • Make sure that your computer is connected correctly to the amplified wireless router using a secured Ethernet cable.
  • Check that you're using an up-to-date and compatible browser. If you're experiencing issues, you can try setting up using a different web browser (recommended: Google Chrome) or close and then open the same browser.
  • Try using the default IP address 192.168.3.1 to access login page instead of web address setup.ampedwireless.com.
  • Try power cycling on the Amped Wireless router.
  • Try to reset your amped wireless router since the rest of the settings back to the factory default settings by pressing and pressing the reset button for a some time before after that, releasing it.

What happens if the internet connection isn't set up in The Smart Setup Wizard automatically?

  • It is necessary to reboot your router by disconnecting it and reconnecting the router.
  • Try to reset the router back to the default settings.
  • If you are using an DSL connection, you'll be required to enter manually your login credentials for the internet service provider.
  • If you are using a the static IP option, you Internet connection might need a fixed IP configuration for which you must contact your ISP to find the IP settings.
  • Your Internet connection might require you to duplicate the MAC address of your PC. To accomplish this, go into More Settings, IP Settings and Internet Network (WAN). From the drop-down menu select the Automatic/Dynamic (DHCP) and copy your PC's MAC address in the DNS setting.

Amped wireless range extender set-up

In the beginning, you have to locate a place that is half way the Wi-Fi router and your Dead Zone for Wi-Fi. Make sure that wherever you place an extender range, it's receiving strong Signal strength coming from the Wi-Fi router.

  • Connect the antennas to the reverse of the range extender.
  • Securely connect your laptop and your range extender.
  • Open any specific web browser and visit www.setup.ampedwireless.com to access the web menu
  • You can choose to use the password-based login IP 192.168.1.240 or alternatively, to access the web menu for the wireless extender with amps.
  • The dashboard of the Web menu appears that displays the state of the extender after which you be required to click Scan to locate any existing networks that can be extended.
  • Choose the wireless networks you wish to extend or repeat. Click Next to proceed further.
  • You will be asked to input a password to you to sign in on your Wireless network. Go to Next to continue
  • Then, you will have to set the settings of your extended network. Enter the your new SSID as well as a passphrase. Select Next, which allows the settings be saved.
  • The wireless range extender restart and you will need connect your computer to the new network.
  • Select OK, and then, your Range extender is now installed successfully.

How can I wirelessly connect with the Amped Wireless range extender?

It's possible with Wi-Fi Protected Setting up or WPS One-Touch Setup, if your wireless adapter supports WPS One-Touch setup.

  • Find the WPS button located in the back on the Amped Wireless Range Extender. press and hold for approximately 3 seconds.
  • The power LED on the wireless router will start to blink.
  • While you're at it push the WPS button that is located on your wireless adapter . You can also enable WPS by using the software available to the wireless adapter.
  • After that, WPS will automatically configure and set the settings for connection to the wireless adapter. It will then join to the Amped Wireless Range Extender.

How can I reset my amplified wireless extender?

Amped's Amped Wireless Range Extender is able to be reset to factory default settings by using the following methods:

Clicking the button Reset

Utilizing Web interface

Resetting by physically pressing the reset buttons is an simple and easy if you follow the instructions below:

  • Find the reset button on the back of the extension of range wireless.
  • With the aid of a straightened clip of paper or pin, push and hold pressing your reset lever for approximately five to ten seconds , and afterwards release it.
  • Take a few minutes until the LED light begins to flash. This is the indication that your Amped Wireless Range Extender is restored to its original settings.

To reset the range extender's amped wireless signal via the web interface, you have to log in to the internet-based interface of the amped wireless router

  • Go to www.setup.ampedwireless.com through a web browser.
  • Log in with your login credentials of default to access the admin section of the amplified wireless.
  • Click on More settings and choose Management.
  • Choose Save/Reload Settings under Management. Click on"Reset Settings" on the default tab to restore the wireless range extender's amp to its factory settings.

What if you are unable to open the web menu of the amped wireless range extender after you enter the www.setup.ampedwireless.com?

  • Check the computer you are using is linked the WIFI network on your range extender
  • Be sure to use an up-to-date and compatible browser. If you're having issues, try setting it up with a different browser (recommended: Google Chrome) or shut down and reopen the same one.
  • Try using the default IP address 192.168.1.240 to access login page instead of web address setup.ampedwireless.com.
  • Try power cycling your Amped Wireless range extender.
  • Reset the range extender since the rest of your settings back to the factory default settings. Resetting the wireless range extender is accomplished by pressing and pressing the reset button for a some time before pressing it again.
  • If none of these steps are working, try disconnecting your PC from connected Wi-Fi networks , and connect your computer to a range extender via the Ethernet cable. Then try to access the web menu of the amped wireless range extender through www.setup.ampedwireless.com.

What happens if the internet isn't accessible through an Amped extension of range wireless?

  • The internet connection on the Home Network might have got lost or the router settings could have changed in some way due to an energy surge or other cause. Therefore, you will need to connect to the Range Extender and access the web interface using the web address http://setup.ampedwireless.com. Use Smart Setup Wizard to connect the Range Extender with your wireless network.
  • Access the setup web menu through setup.ampedwireless.com to check that the signal strength between the Range Extender and your Home Network is above 70%. The issue is that the Range Extender has been placed further away from the router and isn't maintaining a signal strength more than 70 percent. You can test the strength of signal signals between your Router and Range Extender using the left hand side of the menu on the internet and then clicking the More Settings tab, then Management and finally Device Status. The Signal Strength display will appear in the section Home Wireless Network settings. It must be greater than 70 percent. When the strength is less 70%, you'll need to move the amplified Wireless Range Extender towards your router, or move your range Extender.

How do you find the optimal location for your amp extended range wireless device?

It is possible to determine the optimal or ideal signal by using the Signal Strength LED which is in one side of an amplified wireless range extender

  • Great Signal from Green LED over 70 percent
  • The yellow LED is moderately bright. Signal Strength between 60 and 69 percent
  • Red LED: Low Signal strength less than 59 percent
  • It can take three minutes for the LED to show up after switching on the amplified wireless Extender. After the extender has been set up it can be used to direct you on how to position the Extender in a more optimal place. It is suggested that the the signal strength is at least 70% i.e. the LED is green.

NOTE: The signal strength LED will not be lit unless the Range Extender configuration is not completed prior to the.

collect
0
avatar
KnightRides
guide
Zupyak is the world’s largest content marketing community, with over 400 000 members and 3 million articles. Explore and get your content discovered.
Read more