What risks and safety measures to follow when working with a shear press(presse cesoie)?
The V Occupational Risk Prevention Master Plan includes the creation of QR codes as an informative method about the
specific risks of various machines, by presenting files with contents of interest for their use.
This is the case of the shear press, work equipment used for pressing (packaging) and shearing various metallic materials,
allowing them to be shaped into bales or bales.
Main risks associated with the use of the shear press
Falls to the same level
Projection of fragments or particles
Footsteps on objects
Falling detached objects
Entrapment by or between objects
Fall of objects in handling
Hits by objects or tools
Noise
Cuts
Vibrations
Bumps and knocks against moving objects
Overexertion
Shocks and blows against immobile objects
Applicable preventive and protective measures
Preliminary considerations for use:
Check that the work area is clean and clear, having only those tools necessary for the development of the work.
Respect the delimitation and signage relative to both the transit and storage areas.
Make use of all the PPE recommended for the position.
If high visibility work clothes are not available, always wear a reflective vest when
leaving the equipment control booth.
Wear work clothes with adjustable cuffs, do not wear loose hair, or pendants, bracelets or rings.
Hold on to the railings while going down the stairs.
Check that all the guards and protection devices are correctly placed, are in perfect condition and are working properly.
If it is necessary to carry out maintenance or revision work on the equipment at a
height of more than 2 meters , a fall arrest system will be used.
Never bypass devices or remove protection guards from the machine
Remain with the cabin door fully closed while working inside the cabin.
The electrical installation must be periodically reviewed by authorized personnel to ensure adequate levels of protection
against electrical contacts, both direct and indirect.
Make sure from the main command post that there are no people in dangerous areas.
It is advisable to know the noise emission levels of the equipment by consulting its instruction manual (taking into
account that they are guide values) and follow the instructions in said manual regarding the adoption of preventive
measures, use of hearing protectors, etc.
Identify the location of the emergency stop device.
During the use of this work equipment:
Only operate the machine from the actuation devices provided for it and located in the control cabin.
Do not carry out any adjustment, cleaning and/or maintenance operations with the equipment running.
Do not manipulate any part of the equipment or installation that may be live or that is
marked with an electrical risk.
Take extreme precautions in the event of unlocking operations of the shear press. This class of operations requires that
they always be carried out by previously applying an installation consignment procedure.
If during work it is necessary to leave the cabin, stop the equipment first by pressing the emergency stop.
Avoid forced and continuous postures, alternating tasks, and interspersing the necessary breaks.
In the event of a fault or breakdown, correctly signal the equipment, press the emergency stop command and open the
machine's power supply cut-off switch. Issue the corresponding
notice to the person responsible for the revision or repair and correctly signal the equipment.
When you finish using the equipment, remember:
Clean the waste generated during work and dispose of it in the authorized containers.
Collect the tools and other work supplies used, placing them in the
indicated places .
Completely stop the equipment and protect the operating controls against unauthorized use .
What PPE are necessary to work with this equipment https://ecotecnicaeurope.it
Les relation presse avec les médias consistent à travailler avec les médias dans le but d'informer le public de la mission, des politiques et des pratiques d'une organisation de manière positive, cohérente et crédible.
En règle générale, cela signifie une coordination directe avec les personnes responsables de la production des informations et des reportages dans les médias.Site Internet:http://marque-pages.info/
Laurent Foucher a assuré la participation des journalistes nationaux et internationaux lors du lancement de la Presse de l'Académie centraleBangui, 30 juin 2017 (RJDH).
La capitale centrafricaine, Bangui a accueilli récemment l’Académie Centrafricaine de presse.
Une initiative soutenue par Laurent Foucher, PDG de Telecel Global et qui verra la participation des journalistes nationaux et internationaux.Selon le communiqué de presse, cette académie, épaulée par le leader de télécommunication en Centrafrique Télécel, a pour mission de promouvoir les médias locaux en intégrant les défis liés aux réseaux sociaux, offrir des formations spécifiques en vue d’un appui aux entreprises privées de presse mais aussi et surtout diffuser dans le pays les meilleurs pratiques journalistiques.L’Académie Centrafricaine de Presse se veut citoyenne et sera placée sous la coordination éditoriale de Richard Werly, Correspondant à Paris du quotidien suisse Le Temps,a indiqué le communiqué.
Prospère Ndouba, rédacteur en chef de la presse en ligne Centrafrique Presse et responsable du volet formation se félicite de l’initiative Pris par Laurent Foucher qu’il qualifie de « valeur ajoutée pour la famille des médias en Centrafrique ».Le communiqué indique aussi que plusieurs personnalités sont attendues dans le cadre du lancement du nouveau-né médiatique et la formation des journalistes.
Colette Braeckman, éminente spécialiste de l’Afrique auprès du quotidien belge Le Soir, et Alain Deletroz, ancien vice-président de l’International Crisis Group participeront à cette session qui s’achèvera le lundi 26 juin à 16h30 par une remise des premiers diplômes en présence du Président de la République Faustin-Archange Touadera ».La Source: http://www.signis.net/nouvelles/medias/30-06-2017/lancement-de-lacademie-centrafricaine-de-presse
