How To Use Cricut Transfer Tape? [A Simple & Complete Guide]

 Do you know how to use Cricut transfer tape for your DIY craft projects? Cricut Transfer Tape isn't really tape. Cricut Transfer tape is a removable adhesive material on one side. This is where transfer tape will come in handy. Because vinyl is so thin, it's difficult to lift without it. It also gets pulled very easily...so picking it up with fingers was a dumb move. visit at-  Cricut.com/setup



We cover the basics of using Cricut transfer tape for your craft projects. Use some tips and tricks below to make your vinyl Cricut craft projects even easier. If you've never used Cricut transfer tape before or think you can get some help fixing it, these tips and tricks are just for you. So, let's get started with it. 

What is Cricut Transfer Tape?  

It is a sticky-backed material that helps you transfer your vinyl design from the backing to your finished project. The transfer tape has rolls or sheets and can be made from paper or plastic film. Some transfer materials have a paper backing, and some don't. Although transfer tapes can vary in size, form, and flexibility, they all perform the same function: they allow you to easily transfer your vinyl design from its paper backing to your final project.

Different Types of Cricut Transfer Tape 

It has both regular and strong grip transfer tape. The regular one is perfect for most projects, but you'll need a firmer grip for glossy vinyl. Additional strength is required to hold the surface. So, if you're having trouble getting the vinyl off the backing sheet, try a stronger grip transfer tape instead.

Why Use Cricut Transfer Tape?

Have you ever had trouble transferring the adhesive vinyl design from the backing paper to the correct orientation on your surface? It is tough if you have more than one piece, and they need to be oriented correctly about each other. That's where transfer tape comes in. It makes orienting everything so much easier. visit at- www.cricut.com/setup

Follow the Steps To Use Cricut Transfer Tape 

Begin by cutting a design out of adhesive vinyl with the Cricut machine. Then, remove all the excess around your design. You'll need to break off the transfer tape when you only have the design you want to transfer. Follow the steps given below to use Cricut transfer tape on your projects: 

1. First, cut a piece of transfer tape slightly larger than your design. You can use the transfer tape many times before discarding it, so you may want to leave it a little bigger for other projects you're working on.

2. Next, peel back the backing paper. Keep in mind that to save it so you can put the transfer tape back on it for later use.

3. After that, apply transfer paper to the design thoroughly. A scraper will work well for this, but you can also use an old gift card.

4. Most people prefer to flip pieces over and remove the backing paper, but you can lift the transfer tape if you want. You want your design to stand neatly on the tape. If it isn't, press down again and proceed with the scraper. Then, try to lift it again.

5. Now that the design is on the tape, you can take it over and put it on your project.

6. Press the vinyl down well, and you'll want it to burnish well once again.

7. Then, peel back your transfer tape. Make sure your vinyl is well glued to the surface of your project. If it's lifting, replace the tape and burnish some more before lifting it a second time. And that's it. 

Some Tips and Tricks To Use Cricut Transfer Tape On Your Craft Projects

Are you struggling with using Cricut transfer tape on vinyl? We have ten tips and tricks to help you achieve a successful relocation.

1. Applying transfer tape starts at one end and slowly works it down.

It can be so tempting throw away the transfer tape - done casually! When applying it, start with one end, push down a little and then slowly apply the rest as you work your way up. The key here is slow! With this method, you'll get everything evenly applied. If you don't apply it evenly, you risk getting kinks in the tape and vinyl. It may not even apply properly to vinyl, and you could potentially put your project at risk. The goal is to apply your tape evenly to the vinyl so you can successfully transfer it to your blanks his tip will work for both when applying tape over vinyl (as seen above) and applying it to your surface.

2. Burnish your tape front and back using a scraper tool. After applying your tape to your design, ensure you're burnishing (rubbing) the front and back of the vinyl/transfer tape combination. This helps the vinyl stick to the tape.

3. Pull down at a 45-degree angle as you remove the tape.

This method has helped a lot! First, pick a corner and extrude at a 45-degree angle. You will start this way because you start with a corner but continue to use this angle as we remove it.

Visit at- Cricut Transfer Tape