Inspection of your vehicle regularly is important to maintain it in good condition. If you ignore faulty or worn-out brakes then it can become the cause of putting your vehicle and you in danger.
Later this can lead to expensive repairs. If you are looking for a MOT check in Nottingham then you can visit us we have an expert team of testers who will inspect your vehicle in less than an hour. We are also good at providing better car service in Nottingham.
Brakes are one of the most used components in your vehicle, so it’s obvious your brake pads will experience wear and tear over time, but can your vehicle fail in MOT because of worn-out brakes?
Read more to find out which brake issues can lead to MOT failure.
Will My Vehicle Fail Its MOT Due to Worn Brake Pads?
During an MOT test, the tester will check your vehicle's brake discs and pads. If they find out that your vehicle has worn brake pads, they will fail your vehicle in the test.
If the lining of the brake pads wears away, then it will create a negative impact on braking efficiency. So if the brake pads are worn below 1.5mm then it becomes the reason for MOT failure.
If you notice that your brake pads soon the legal limit, then you may get an advisory warning instead it is better to replace them with a new one. Most of the time this happens when your brake pads are below 3mm.
On average brake pads last approximately 50,000 miles with proper care, but this number may vary depending on the driving style and the road you are driving on.
How Are Brakes Tested During an MOT Test?
A tester will check your vehicle's braking system to understand the physical condition and efficiency of the braking components. They will check different braking components which are located underneath the vehicle.
The MOT tester will inspect the condition of the following components:
- Brakes
- Brake fluid
- Handbrake
- Anti-lock braking system (ABS)
- Electronic braking system (EBS)
The tester visually inspects the brake pads and looks for any wear and tear on the braking system.
They will also check the ABS warning lights and its other operations during the MOT inspection. If the footbrake touches the floor, the brake pedal rubber or pedal pivot is worn out, or the servo assistance system is not working then the tester can fail you in MOT.
The brake pedal will fail if the test finds out the grooves or raised grip sections on the pedal are completely worn out. However, if your vehicle was manufactured with a brake pedal that does not have anti-slip material or grooves then the tester will not fail the brake pedal.
Most modern vehicles have dashboard warning lights. It can show most of the problems of your vehicle on the dashboard such as when the brake pads are wearing out.
The MOT tester will easily fail your vehicle if they these warning lights without checking the components. So replace your brake pads or other faculty brake components before going for the test.
Brake Problems Which Result in MOT Failure
Several common brake issues can become the cause of MOT failure.
Brake Juddering (Steering & Suspension Vibration)
When you apply your brakes you may notice a slite juddering. This can happen by the brake pads pressing unevenly on the brake discs. You can also feel the steering vibration if you leave your vehicle parked for longer periods.
If the is some residue on the brakes because of hard stopping or if the disc brake has warped from keeping your foot on the brake in traffic then this can also lead to a juddering sensation.
Issues in Brake Pedal
As we said earlier if the grooves or raised grip sections of the brake pedal are completely worn, this will result in MOT failure, unless the vehicle was manufactured with a brake pedal that does not have grooves or anti-slip material.
Contaminated or Leaking Brake Fluid
If the brake fluid is contaminated they will treat it as a defect. Your vehicle will fail in the MOT test if the tester can see the brake fluid is contaminated. If the brake fluid is leaking, it can be a dangerous fault in the eye of the MOT tester.
Some minor defects which the tester takes into consideration include the minimum level of brake fluid, or the brake fluid warning light being illuminated. However, these minor defects will not lead to an MOT failure right away, but you will be advised by the tester to resolve these defects as soon as possible.
Conclusion
We hope that you learn about some brake problems which can lead to MOT failure. If you are planning to go for a MOT check in Nottingham then you can come to us. We have an experienced team of MOT testers who will perform the test in less than an hour. If your car needs repair or service then don’t need to worry, we also offer car service in Nottingham.
Abstract: Brake Pads are components of brake systems used in automotive and other applications.
Brake pads are friction materials which bound to the surface that faces the brake rotor and take the brunt of the frictional force necessary to stop the car.
In a disc brake system, the brake pedal activates a hydraulic line which squeezes the calipers against the rotors of the car's tires.
Pads are positioned between the calipers and the rotors to absorb the energy and heat, and then provide enough grips to stop the car.Download FREE Sample of this Report @ https://www.24chemicalresearch.com/download-sample/33536/global-brake-pads-2019-103 According to this study, the global Brake Pads market is valued at 10.34 Billion USD in 2017 and is expected to reach 11.61 Billion USD by the end of 2025, growing at a CAGR of 1.42% between 2017 and 2025.
As we can see from the past few years, the brake pads industry has developed rapidly for many years and the technology is mature.
The key manufacturers mainly distribute in USA, Europe and Japan regions, where the automobile industry is quite developed.
Are you looking for high-quality brake pads for your sports car?
If so, then we at Race Brake Shop provide you with the premium BMW G-LOC Brakes which feature a unique brake pad technology.
These braking pads are now being used by pro racers, club racers, tuners, etc.
The R12 compound of our gloc pads has better fade resistance and initial bite.
