Sachiya Steel International is one of the Leading Manufacturer And Exporter Of High-Quality Stainless Steel 410 Beam, which is also characterized by high ductility and impact strength. Stainless Steel 410 Angle is austenitic stainless steel offering excellent resistance to intergranular corrosion following exposure to temperatures in the chromium carbide precipitation range from 800 Degree to 1500 Degree F. Stainless Steel 410 C-Channel is well suited for applications related to chemical processing, heat exchangers, desalinization, and more. With its high levels of chromium, molybdenum, and nitrogen, Stainless Steel 410 H-Beam has excellent resistance to a wide range of chemicals.
Phone No: +91 9769056007
Email id: [email protected]
Website: https://www.steelpipesfactory.in/stainless-steel-410-beam/
Sachiya Steel International is one of the Leading Manufacturer And Exporter of Stainless Steel 410 Flanges, where better finishes are obtained in the cold drawn or heat – treated condition.
In its softest condition, these Stainless Steel 410 Slip On Flanges is tough and chips build up on tools.
If higher mechanical properties are required, our Stainless Steel 410 Threaded Flanges can be machined.
Our Stainless Steel 410 Weld Neck Flanges are low carbon steels built around the composition of iron, 12 % chromium, and 0.12 % carbon.
These Stainless Steel 410 Blind Flanges provides good corrosion resistance to air, water and some chemicals, where resistance to food acids is good.Our Stainless Steel UNS S41000 Socket Weld Flanges shows satisfactory resistance to nitric acid, concentrated sulphuric acid, dilute acetic acid and naphtha.
These Stainless Steel 410 Lap Joint Flanges has extensive use in aircraft parts, such as exhaust systems where operating temperatures are higher than 800 Degree F and where corrosive conditions are not too severe; also for the reason that of its resistance to scaling and vibration fatigue.Stainless Steel 410 Flanges | Stainless Steel 410 Flanges | Stainless Steel 410 Flanges | Stainless Steel 410 Flanges | Stainless Steel 410 Flanges | Stainless Steel 410 Flanges | Stainless Steel 410 FlangesOur Stainless Steel 410 Ring Joint Type Flanges may be tempered and hardened, which gives steel great hardness, but also reduces its toughness and makes it brittle, so few steels are fully hardened.
Sachiya Steel International is one of the Leading Manufacturer And Exporters of Stainless Steel 410 Threaded Forged Fittings, which display good resistance to scaling in continuous service up to 650 Degree C. Small sections of Stainless Steel 410 Forged Threaded Elbow can be air-cooled, and larger sections of oil quenched for maximum through hardness.
Prehardened and tempered Stainless Steel 410 Forged Threaded Tee will also respond readily to nitriding achieving a typical surface hardness.The nitriding process of Stainless Steel 410 Forged Threaded Cross however reduces the corrosion resistance and is therefore not generally recommended except for critical applications where the benefit outweighs all other considerations.
Stainless Steel 410 Forged Threaded Cap is used for parts requiring a combination of good strength and toughness, plus reasonable corrosion resistance.
Use of Stainless Steel 410 Forged Threaded Fittings at higher working temperatures results in a substantial drop in tensile strength and hardness with a subsequent increase in ductility.Stainless Steel 410 Threaded Forged Fittings | Stainless Steel 410 Threaded Forged Fittings | Stainless Steel 410 Threaded Forged Fittings | Stainless Steel 410 Threaded Forged Fittings | Stainless Steel 410 Threaded Forged Fittings | Stainless Steel 410 Threaded Forged Fittings | Stainless Steel 410 Threaded Forged Fittings Stainless Steel 410 Forged Threaded Coupling is not recommended for use at sub–zero temperatures due to a substantial drop in impact properties consistent with most steels other than the austenitic steel types.
In the hardened and tempered as supplied condition, Stainless Steel 410 Forged Threaded Union will be more difficult due to the high yield strength which must be taken into account.Stainless Steel 410 Forged Threaded Fittings SpecificationsSpecifications:ASTM A182 & ASME SA182Size:1/8” NB to 4” NB (Socket weld & Screwed-Threaded)Standards:ASME 16.11, MSS SP-79, 83, 95, 97, BS 3799Class:2000 LBS, 3000 LBS, 6000 LBS, 9000 LBSType:Threaded Fittings SS 410 Forged Fittings Chemical Composition GradeCMnSiPSCrMoNiNSS 4100.15 max1.00 max1.00 max0.040 max0.030 max11.50 – 13.50–0.75 max– Stainless Steel 410 Threaded Fitting Mechanical Properties DensityMelting PointTensile StrengthYield Strength (0.2%Offset)Elongation7.8 g/cm31400 °C (2550 °F)Psi – 65000 , MPa – 450Psi – 30000 , MPa – 20520% Equivalent Grades for 410 Stainless Steel Forged Fittings STANDARDWERKSTOFF NR.UNSJISBSGOSTAFNORENSS 4101.4006S41000SUS 410410S21––X12Cr13 Stainless Steel 410 Forged Fittings Application Industries Off-Shore Oil Drilling CompaniesPower GenerationPetrochemicalsGas ProcessingSpecialty ChemicalsPharmaceuticalsPharmaceutical EquipmentChemical EquipmentSea Water EquipmentHeat ExchangersCondensersPulp and Paper IndustryAbout Us: Sachiya Steel International are manufacturers & exporters of Pipes, Tubes, Pipe Fitting, Fasteners.Sachiya Steel International is an internationally acclaimed Pipes And Tubes manufacturing company that exports to more than 90 countries worldwide.
We export our high-quality fasteners in Saudi Arabia, Oman, UAE, Dubai, Kuwait, Qatar, Mexico, the USA, Malaysia, Iran, and many other countries.Email: [email protected] More Information Visit Our Website: Steel Tube
Sachiya Steel International is one of the Leading Manufacturer And Exporter of Stainless Steel 410 Round Bar, which are generally considered to have slightly poorer weldability than the most common ferritic stainless steel grade.
Special consideration of Stainless Steel 410 Square Bars should be given to avoid brittle weld fractures during fabrication by minimizing discontinuities, maintaining low weld heat input and occasionally warming the part somewhat before forming.
A major difference can be attributed to the addition of Stainless Steel 410 Flat Bars to control hardening which results in the need for higher heat input to achieve penetration during arc welding.When weld filler is required, Stainless Steel 410 Threaded Bars is most often specified immersed in a warm solution of 10 % – 20 % nitric acid followed by a water rinse to remove any residual iron.
Stainless Steel 410 Hollow Bars contains a minimum of 12 % chromium, just sufficient enough to give corrosion resistant properties.
Stainless Steel 410 Hexagonal Bars has higher carbon content which is designed to optimize strength and hardness characteristics.Stainless Steel 410 Round Bar | Stainless Steel 410 Round Bar | Stainless Steel 410 Round Bar | Stainless Steel 410 Round Bar | Stainless Steel 410 Round Bar | Stainless Steel 410 Round Bar | Stainless Steel 410 Round Bar | Stainless Steel 410 Round BarStainless Steel 410 Triangular Bars has good ductility it the annealed condition but is capable of being hardened the highest hardness of the 12 % chromium grades.
Due to its hardening properties, Stainless Steel 410 Bars is not often welded, although it is possible.
Sachiya Steel International is one of the Leading Manufacturer And Exporter of Stainless Steel 410 Pipe Fittings, which is available in reasonable price to our esteemed clients.
Stainless Steel 410 Compression Pipe Fittings is a columbium / tantalum stabilized austenitic stainless steel, and has excellent resistance to inter – granular corrosion.
SS 410 Compression Fittings should be considered for applications requiring intermittent heating between 800 Degree F / 1650 Degree F (425 Degree C / 900 Degree C).
SS 410 Accessories is resistant to atmospheric corrosion, foodstuffs, sterilizing solutions, many organic and inorganic chemicals and dyestuffs.Because of its low columbium and tantalum contents, Stainless Steel 410 Ferrule Pipe Fittings should be considered for nuclear applications.
Heat this Stainless Steel 410 Double Ferrule Pipe Fittings uniformly to forging temperature, 2100 Degree F / 2250 Degree F (1150 Degree C / 1230 Degree C) and then forge, but do not forge below 1700 Degree F (925 Degree C).
Forgings in 410 Stainless Steel Compression Pipe Fittings may be air cooled, but for maximum corrosion resistance forgings must be water quenched or subsequently annealed.Stainless Steel 410 Pipe Fittings | Stainless Steel 410 Pipe Fittings | Stainless Steel 410 Pipe Fittings | Stainless Steel 410 Pipe Fittings | Stainless Steel 410 Pipe Fittings | Stainless Steel 410 Pipe Fittings410 Stainless Steel Ferrule Pipe Fittings is used in rigid tooling and positive feeds for best machinability, and if possible a little cold work on stock to be machined.
